Introduction
For those times when you need a break from the EM Discharge meta. Though not as ammo efficient, I find this build more engaging and exciting to play. It allows you to have high single target damage from Executioner, along with decent wave clear from Blowthrough Rounds and your Breach Cutter. I haven't run into any ammo problems yet on Hazard 6.
Perks: Vampire, Thorns, Born Ready | Dash, Iron Will/Heightened Senses
Grenade: Plasma Burster
Build Explanation
LOK-1
- Tier 1: Increased Caliber Rounds give you a lower time to kill for High Value Targets. I also find that, counterintuitively, if you line up your shots correctly you can kill multiple targets with less ammo because of damage breakpoints and Blowthrough Rounds (to be discussed bellow). Feel free to take Expanded Ammo Bags if you really find yourself struggling in between resupplies.
- Tier 2: Macro Lens is the obvious choice here. Limiting the scope of your lock acquisition allows you to better isolate targets to lock onto, helping you be more precise and conserve ammo. Two times range is pretty self explanatory.
- Tier 3: Blowthrough Rounds is pretty key to ammo conservation and wave clearing in this build. The game plan is as follows: line up several enemies, apply full locks on the lead grunt, and angle your bullets to pass through as many as you can with Blowthrough Rounds. You'll have to get good at bending bullets, but this strategy allows you to conserve ammo on swarms. Don't forget to aim for weakpoints to proc Executioner.
- Tier 4: Shutter Speed Sensor is the only real choice in this slot. Faster Lock acquisition is much better than more locks, even more so considering we are actively trying to limit the number of targets we are locking onto with this build.
- Tier 5: Since you'll be going for full locks almost all the time in order to proc Executioner, Unstable Lock Mechanism makes the most sense here. Since we are choosing Blowthrough Rounds over electricity in tier 3, Electric Generator doesn't help us much.
Breach Cutter
My Breach Cutter build is essentially the same as a lot of other Hazard 6 Engineer builds I've seen on here. In my opinion, the Breach Cutter beats out the PGL quite easily on higher hazard levels for its hybrid AOE and single target capabilities (the PGL really only specializes in one or the other). You could make several overclocks work for this build, but I personally prefer Inferno, as fire status spreads to multiple enemies, and the flame DOTS will kill spitballers in 1 shot if you leave them long enough. Each of these attributes are clutch at higher hazard levels. For this build, the Breach Cutter is essentially a combination hail-Mary wave-clearer, and single-target softener for Executioner.
- Tier 1: Increased projectile lifetime = longer range, which will help you immensely dealing with Spitball Inspectors and Breeders. These will be multitudinous in the modded difficulties. Also, with Plasma Trail in tier 5 and DOTS from Inferno, you can easily clear huge waves of swarmers, flying jellyfish, and grunts.
- Tier 2: More ammo is a no-brainer here.
- Tier 3: Quick Deploy is incredibly important for those "oh crap" moments, of which you will have many at Hazard 6+, where the bugs are faster, hit harder, and are more plentiful. Reload times aren't really an issue with Born Ready and animation cancelling (which you should already be doing if you're playing Haz 6).
- Tier 4: Disruptive Frequency Timing gives you some much needed CC and breathing room during those aforementioned "oh crap" moments.
- Tier 5: Plasma Trail really helps with swarmers and shockers. Refer to explanation given above for more detail.
Turrets
My personal preference is a turret build that facilitates more of a "Set it and forget it" play style. This is the turret setup I use for most of my engie builds. Just make sure you set and forget your turrets in an advantageous and elevated position with clear sight lines. Also, make sure that your turrets are positioned so that they are easy to restock in a hurry. And don't forget to reset and forget your turrets when you move positions. The 4 second build time is tough to get used to at first, but the increased ammo will really help you when you're fighting big waves. Your turrets are arguably the most valuable part of your kit for dealing with swarms (this is essentially true in any Engineer build). An argument could be made for any of the three choices in tier 3, I personally choose Penetrating Rounds most of the time to make up for Inferno's armour break penalty.